Mold 1 of 5 Complete!
16 days ago
– Sat, Jul 06, 2019 at 12:15:21 AM
Macintosh SE & SE/30 Programmers Switch Mold Complete
The first of five molds is complete. This mold, being the smallest and simplest, was completed first. The other molds are still in progress. We will update when the next mold is complete. Please check out the photos below illustrating the mold and finished product.
Inner Mold Cavity
The photo below shows the inside mold cavity. Notice the highly polished mirror finish. This was achieved by a ten stage polishing process. This is required to achieve the high level of transparency desired.
Second Side of the Mold Plate
The photo below shows the opposite side of the mold where the polycarbonate plastic is injected. Additionally, holes for the ejector pins are visible which are required to remove the button assemblies from the mold.
The photo below shows the output of the mold above. The photos were taken on the factory floor and do not do the buttons justice. They have a nice level of clarity and are quite durable.
Please stay tuned for updates!
Mold Design Complete!
2 months ago
– Tue, May 21, 2019 at 10:17:11 PM
Mold Design Complete
Pending final engineering approval the molds for the front and rear cases are both complete. Production on the molds are expected to start within a week. Below are some sample drawings of the molds.
Also, starting tomorrow May 22nd we will be sending a survey to a random sample to 5% of the Backers which will include: a survey regarding potential future cases, the option to get add on accessories, and a spot to add shipping information required to send pledged rewards. By the May 25th, everyone should receive a survey e-mail. Please make sure to complete the survey even if you do not wish to have any add on accessories as the survey regarding future products is important.
Mold Design View 1
Mold Design View 2
We Did It! All Goals Are Fully Funded!
2 months ago
– Sun, May 12, 2019 at 04:04:24 PM
Success - We Reached All the Goals!
We have reached the goals required to produce all of the add-on items. We wish to give a special thanks to everyone who has been involved in the project, especially all of the backers.
We have already completed the DFM (Design for Manufacturing) process for the front and rear case. Work has already began on engineering the molds.
Below is a detail of what will be happening next:
Within 7-14 days a survey will be sent requesting address information. It will also contain the option to add on the front case, mouse case, or programmers switch. Some of the payment processing methods are expected to fail for various reasons including expired or incorrect information, but random checks by the payment processor will happen. There is a 7 day limit on payment corrections, so please make sure to follow Kickstarter's instructions on correcting payments to remain eligible for this project.
- Within 12-20 days engineering the main molds will be complete and move to mold production.
- When complete with mold engineering will be an additional 30-45 days of mold manufacturing.
- The next step is final production prototypes (using the final method) it will also include one of each of the various colors.
- Upon approval production of the cases will begin (projected for July)
Backers are expected to receive their rewards by no later than October or November (depending on reward)
When the surveys arrive please understand that the photos are just for demonstrative purposes. The color and tint of the cases will vary. The mouse is waiting for its final approval and no picture is available for the mouse case.
We will continue to post updates of important phases at least once a month, so please keep checking back.
Success - Front Case for the Macintosh SE/30 will be Produced!
2 months ago
– Wed, May 08, 2019 at 11:35:47 PM
Front Case for the Macintosh SE/30 will be Produced!
While we are a bit short of our second goal with 3 days left, we wanted to recognize the massive support by producing the front case panel regardless of the final amount raised! The front case panel will be available as an add-on when the backer survey is sent. Please be sure to select this option if you would like one for your case.
Even more exciting is that we have dropped the ADB mouse and programmers switch goal to $25,000. That means only $1,754 to go in 3 days and these will be produced. Please be sure to see our updated stretch goals shown below.
Thank you everyone for your support. Please continue to share this Kickstarter so that we can get the mouse and programmers switch.
Almost There! We Have an Exciting Macintosh SE & SE/30 Project Update!!
3 months ago
– Sun, Apr 28, 2019 at 05:15:09 PM
Right now we are only $2,095 away from our second stretch goal with only 13 days left. To reward everyone for their great efforts in sharing the project, we have a special surprise addition to this project. We have created a clear programmers switch prototype (shown below). If we can get to $26,000 this add-on becomes a reality!
We Aren't There Yet!
To make sure we make everything in this project a reality we wanted to provide some additional benefits for backing this project. If we reach the second stretch goal ($25,000) by Friday May 3rd, we will drop the goal for the mouse from $30,000 to $27,000!
If We Get to $25,000 by May 3rd the Projected Stretch Goals will Be:
- Rear Rear - $15,000
- Front Case - $25,000
- Programmers Switch - $26,000
- ADB Mouse Case - $27,000
Please be Sure to Share the Project